ARK Documentation
  • ARK Electronics Docs
  • Embedded Computers
    • ARK Just A Jetson
      • Flashing Guide
      • Connections
      • Pinout
      • Block Diagram
      • 3D Model
  • Flight Controller
    • ARK FPV
      • Pinout
      • PX4 Instructions
      • ArduPilot Instructions
      • Betaflight Instructions
      • Bootloader Flashing Using DFU
      • 3D Models
    • ARKV6X
      • PX4 Instructions
      • ArduPilot Instructions
      • 3D Models
    • ARK Pixhawk Autopilot Bus Carrier
      • 3D Models and Case Files
      • Pinout
      • PX4 Instructions
    • ARK Jetson PAB Carrier
      • Getting Started
      • Block Diagram
      • Pinout
      • 3D Models and Case Files
      • Flashing Guide
      • ARK Software
        • Services
      • Autopilot Connections
      • Updating the Flight Controller Firmware
      • Micro USB Console
      • Power Cycling USB Ports
      • Mini DisplayPort
      • USB Wi-Fi Adapters
      • USB Bluetooth Adapters
    • ARK Pi6X Flow
      • Block Diagram
      • Pinout
      • 3D Models
      • Flashing Guide
        • Pi CM4 Lite with Micro SD
        • Pi CM4 with EMMC
        • After Flashing, Before Installing
        • Wi-Fi Setup
        • SSH
      • ARK Software
        • Services
      • Autopilot Connections
      • Updating the Flight Controller Firmware
    • ARK VOXL2 RTK PAB Carrier
      • Pinout
      • Connectors and Cables
      • 3D Models
      • Autopilot Connections
  • Electronic Speed Controller
    • ARK 4IN1 ESC
      • Pinout
      • Firmware
      • PWM Calibration
      • 3D Models
  • Radio
    • ARK M.2 LTE
      • OpenVPN
    • ARK Microhard DDL Carrier
      • 3D Model
  • Sensor
    • ARK Flow
      • Ardupilot Instructions
      • PX4 Instructions
      • 3D models & Case files
    • ARK Flow MR
      • Ardupilot Instructions
      • PX4 Instructions
      • 3D models & Case files
    • ARK CANnode
      • PX4 Instructions
      • 3D Models
  • GPS
    • ARK GPS
      • PX4 Instructions
      • 3D Models
    • ARK MOSAIC-X5 RTK GPS
    • ARK RTK Base
      • 3D Model
    • ARK RTK GPS
      • RTK Heading (Ardupilot)
      • RTK Heading (PX4)
    • ARK TESEO GPS
    • ARK SAM GPS
      • PX4 Instructions
      • Ardupilot Instructions
      • Betaflight Instructions
      • 3D Model
  • Power
    • ARK PAB Power Module
      • PX4 Instructions
      • ArduPilot Instructions
      • 3D Model
    • ARK 12S PAB Power Module
      • PX4 Instructions
      • ArduPilot Instructions
      • 3D Model
  • IMU
    • ARK ADIS16507
      • PX4 Instructions
      • ArduPilot Instructions
      • 3D Model
    • ARK SCH16T
      • PX4 Instructions
      • ArduPilot Instructions
      • 3D Model
  • ROS2 & PX4
    • Mastering Precision Landing with PX4 & ROS2
    • Aruco Detectios Tutorial
    • Custom Modes Hardware Demo with PX4 & ROS2
    • Utilizing Custom Modes in PX4 with ROS2 and QGC
    • Simulated Offboard Mode
  • PX4 Log Encryption
  • Radio Integration
    • Doodle Labs Nimble Integration Guide for ARK Jetson PAB Carrier
  • Resources
    • Links
    • About
Powered by GitBook
On this page
  • Pinout
  • Assembly
  • Disassembly
  1. Radio

ARK Microhard DDL Carrier

Microhard Pico DDL carrier supporting USB C power delivery and battery power up to 55V

PreviousOpenVPNNext3D Model

Last updated 2 months ago

Pinout

BAT - 2 Pin Molex Nano-Fit 1054301202 - Mates with

Pin Number
Signal Name
Voltage

1

BAT_IN

5.5V - 55V

2

GND

GND

LAN - 4 Pin JST-GH

Pin Number
Signal Name
Voltage

1

LAN_RD_N

50V

2

LAN_RD_P

50V

3

LAN_TD_N

50V

4

LAN_TD_P

50V

WAN - 4 Pin JST-GH

Pin Number
Signal Name
Voltage

1

WAN_RD_N

50V

2

WAN_RD_P

50V

3

WAN_TD_N

50V

4

WAN_TD_P

50V

Serial - 6 Pin JST-GH

Pin Number
Signal Name
Voltage

1

No Connect

No Connect

2

FC_TX_OUT_RADIO_RX_IN_EXT

3.3V

3

FC_RX_IN_RADIO_TX_OUT_EXT

3.3V

4

FC_CTS_IN_RADIO_CTS_OUT_EXT

3.3V

5

FC_RTS_OUT_RADIO_RTS_IN_EXT

3.3V

6

GND

GND

Assembly

  1. Remove all connections from the board.

  2. Place the thermal pad on the copper in the socket.

  3. Insert the Microhard module with the antenna connectors nearest to the edge of the board.

Disassembly

  1. Remove all connections from the board.

  2. Using a small screwdriver, pry the non-antenna connector corner from the socket. Being careful to not damage the PCB or socket. Prying against the metal RF shield works well.

  3. Remove the thermal pad.

45130
ARK Microhard DDL Carrier Connections
Page cover image