ARK Documentation
  • ARK Electronics Docs
  • Embedded Computers
    • ARK Just A Jetson
      • Flashing Guide
      • Connections
      • Pinout
      • Block Diagram
      • 3D Model
  • Flight Controller
    • ARK FPV
      • Pinout
      • PX4 Instructions
      • ArduPilot Instructions
      • Betaflight Instructions
      • Bootloader Flashing Using DFU
      • 3D Models
    • ARKV6X
      • PX4 Instructions
      • ArduPilot Instructions
      • 3D Models
    • ARK Pixhawk Autopilot Bus Carrier
      • 3D Models and Case Files
      • Pinout
      • PX4 Instructions
    • ARK Jetson PAB Carrier
      • Getting Started
      • Block Diagram
      • Pinout
      • 3D Models and Case Files
      • Flashing Guide
      • ARK Software
        • Services
      • Autopilot Connections
      • Updating the Flight Controller Firmware
      • Micro USB Console
      • Power Cycling USB Ports
      • Mini DisplayPort
      • USB Wi-Fi Adapters
      • USB Bluetooth Adapters
    • ARK Pi6X Flow
      • Block Diagram
      • Pinout
      • 3D Models
      • Flashing Guide
        • Pi CM4 Lite with Micro SD
        • Pi CM4 with EMMC
        • After Flashing, Before Installing
        • Wi-Fi Setup
        • SSH
      • ARK Software
        • Services
      • Autopilot Connections
      • Updating the Flight Controller Firmware
    • ARK VOXL2 RTK PAB Carrier
      • Pinout
      • Connectors and Cables
      • 3D Models
      • Autopilot Connections
  • Electronic Speed Controller
    • ARK 4IN1 ESC
      • Pinout
      • Firmware
      • PWM Calibration
      • 3D Models
  • Radio
    • ARK M.2 LTE
      • OpenVPN
    • ARK Microhard DDL Carrier
      • 3D Model
  • Sensor
    • ARK Flow
      • Ardupilot Instructions
      • PX4 Instructions
      • 3D models & Case files
    • ARK Flow MR
      • Ardupilot Instructions
      • PX4 Instructions
      • 3D models & Case files
    • ARK CANnode
      • PX4 Instructions
      • 3D Models
  • GPS
    • ARK GPS
      • PX4 Instructions
      • 3D Models
    • ARK MOSAIC-X5 RTK GPS
    • ARK RTK Base
      • 3D Model
    • ARK RTK GPS
      • RTK Heading (Ardupilot)
      • RTK Heading (PX4)
    • ARK TESEO GPS
    • ARK SAM GPS
      • PX4 Instructions
      • Ardupilot Instructions
      • Betaflight Instructions
      • 3D Model
  • Power
    • ARK PAB Power Module
      • PX4 Instructions
      • ArduPilot Instructions
      • 3D Model
    • ARK 12S PAB Power Module
      • PX4 Instructions
      • ArduPilot Instructions
      • 3D Model
  • IMU
    • ARK ADIS16507
      • PX4 Instructions
      • ArduPilot Instructions
      • 3D Model
    • ARK SCH16T
      • PX4 Instructions
      • ArduPilot Instructions
      • 3D Model
  • ROS2 & PX4
    • Mastering Precision Landing with PX4 & ROS2
    • Aruco Detectios Tutorial
    • Custom Modes Hardware Demo with PX4 & ROS2
    • Utilizing Custom Modes in PX4 with ROS2 and QGC
    • Simulated Offboard Mode
  • PX4 Log Encryption
  • Radio Integration
    • Doodle Labs Nimble Integration Guide for ARK Jetson PAB Carrier
  • Resources
    • Links
    • About
Powered by GitBook
On this page
  • Cooling
  • Capacitor and TVS Diode
  1. Power

ARK 12S PAB Power Module

Previous3D ModelNextPX4 Instructions

Last updated 5 months ago

The ARK 12S PAB Power Module is rated for 100A continuous battery current at 20C ambient. It is recommended to run multiple power modules in parallel if more than 100A continuous current is required.

The board uses an INA238 digital power monitor with a 0.1mΩ shunt to measure voltage and current over I2C. A 5.2V 6A regulator outputs power to the avionics using a 6 pin Molex CLIK-Mate connector that matches the pinout on the ARK PAB Carriers.

Cooling

When operating at high battery current and/or high 5V regulator output current, it is recommended to actively cool the board.

Capacitor and TVS Diode

When operating with 12S batteries, it is recommended to solder the included capacitor and TVS diode to the output side of the board. The negative of the capacitor is indicated on the cylinder. The cathode(line) on the TVS diode should be soldered to the positive side of the output.

PX4 Instructions
ArduPilot Instructions
3D Model
12S with Capacitor and TVS Diode
Page cover image