ARK Documentation
  • ARK Electronics Docs
  • Embedded Computers
    • ARK Just A Jetson
      • Pinout
      • Block Diagram
      • Flashing Guide
      • 3D Model
  • Flight Controller
    • ARK FPV
      • Pinout
      • PX4 Instructions
      • ArduPilot Instructions
      • Betaflight Instructions
      • Bootloader Flashing Using DFU
      • 3D Models
    • ARKV6X
      • PX4 Instructions
      • ArduPilot Instructions
      • 3D Models
    • ARK Pixhawk Autopilot Bus Carrier
      • 3D Models and Case Files
      • Pinout
      • PX4 Instructions
    • ARK Jetson PAB Carrier
      • Getting Started
      • Block Diagram
      • Pinout
      • 3D Models and Case Files
      • Flashing Guide
      • ARK Software
        • Services
      • Autopilot Connections
      • Updating the Flight Controller Firmware
      • Micro USB Console
      • Power Cycling USB Ports
      • Mini DisplayPort
      • USB Wi-Fi Adapters
      • USB Bluetooth Adapters
    • ARK Pi6X Flow
      • Block Diagram
      • Pinout
      • 3D Models
      • Flashing Guide
        • Pi CM4 Lite with Micro SD
        • Pi CM4 with EMMC
        • After Flashing, Before Installing
        • Wi-Fi Setup
        • SSH
      • ARK Software
        • Services
      • Autopilot Connections
      • Updating the Flight Controller Firmware
    • ARK VOXL2 RTK PAB Carrier
      • Pinout
      • Connectors and Cables
      • 3D Models
      • Autopilot Connections
  • Electronic Speed Controller
    • ARK 4IN1 ESC
      • Pinout
      • Firmware
      • PWM Calibration
      • 3D Models
  • Radio
    • ARK M.2 LTE
      • OpenVPN
    • ARK Microhard DDL Carrier
      • 3D Model
  • Sensor
    • ARK Flow
      • Ardupilot Instructions
      • PX4 Instructions
      • 3D models & Case files
    • ARK Flow MR
      • Ardupilot Instructions
      • PX4 Instructions
      • 3D models & Case files
    • ARK CANnode
      • PX4 Instructions
      • 3D Models
  • GPS
    • ARK GPS
      • PX4 Instructions
      • 3D Models
    • ARK MOSAIC-X5 RTK GPS
    • ARK RTK Base
      • 3D Model
    • ARK RTK GPS
    • ARK TESEO GPS
    • ARK SAM GPS
      • PX4 Instructions
      • Ardupilot Instructions
      • Betaflight Instructions
      • 3D Model
  • Power
    • ARK PAB Power Module
      • PX4 Instructions
      • ArduPilot Instructions
      • 3D Model
    • ARK 12S PAB Power Module
      • PX4 Instructions
      • ArduPilot Instructions
      • 3D Model
  • IMU
    • ARK ADIS16507
      • PX4 Instructions
      • ArduPilot Instructions
      • 3D Model
    • ARK SCH16T
      • PX4 Instructions
      • ArduPilot Instructions
      • 3D Model
  • ROS2 & PX4
    • Mastering Precision Landing with PX4 & ROS2
    • Aruco Detectios Tutorial
    • Custom Modes Hardware Demo with PX4 & ROS2
    • Utilizing Custom Modes in PX4 with ROS2 and QGC
    • Simulated Offboard Mode
  • PX4 Log Encryption
  • Radio Integration
    • Doodle Labs Nimble Integration Guide for ARK Jetson PAB Carrier
  • Resources
    • Links
    • About
Powered by GitBook
On this page
  • Accessing the Jetson console over the micro USB
  • Connecting to WiFi using the micro USB port
  • Creating a WiFi hotspot using the command line
  1. Flight Controller
  2. ARK Jetson PAB Carrier

Micro USB Console

PreviousUpdating the Flight Controller FirmwareNextPower Cycling USB Ports

Last updated 10 months ago

Plugging in a micro USB cable to the Jetson carrier will disconnect the OTG port from the flight controller and turn the Jetson into a device. A file system is mounted and a serial port is presented the the host PC.

The L4T-README drive contains text files with information on using the serial port and connecting WiFi.

After disconnecting the micro USB you must reboot the Jetson to reconnect the OTG port to the flight controller.

Accessing the Jetson console over the micro USB

After connecting, find the serial port number in your OS of choice. Using a serial terminal program, connect to that port using baud rate 115200.

You will need to login with your username and password. If you followed the flashing guide in these docs, it will be username "jetson" password "jetson".

Connecting to WiFi using the micro USB port

If you installed an M.2 WiFi module or a USB WiFi dongle, you can use nmcli to connect using the command line.

To scan for available networks:

sudo nmcli device wifi

To connect to a network

sudo nmcli device wifi connect 'SSID' password 'PASSWORD'

Creating a WiFi hotspot using the command line